Screen-Mounted Dual-Phone Holder for Tesla Model 3 / Model Y

Screen-Mounted 2-in-1 Phone Holder for Tesla Model 3 / Model Y

Mount your phone beside the Tesla center display without adhesive, drilling or permanent dashboard modification. A telescopic alloy support arm clamps mechanically to the back of the touchscreen and works with interchangeable gravity-cradle and magnetic phone-mount attachments.

Phone Access Without Dashboard Adhesive

Mechanical Screen Mount
The holder attaches around the rear frame of the center touchscreen rather than relying on glue or adhesive tape.

Adjustable Viewing Position
The telescopic arm and rotating joint allow the phone position to be adjusted for different drivers and viewing preferences.

Interchangeable Phone Attachments
Switch between the included gravity cradle and magnetic pad depending on your phone, case and preferred mounting method.

⚠️ “Dual” Refers to the Current 2-in-1 Mounting System

The current product page confirms that the holder includes both a gravity cradle and a magnetic pad that can be swapped on the standard 17 mm joint. The published description does not clearly confirm simultaneous support for two phones, so this listing does not promise two-device use at the same time.

Mechanical Touchscreen Mount

The support arm locks mechanically around the back frame of the Tesla center display. No adhesive pad is required on the dashboard or screen surface.

This installation method is useful for owners who prefer a removable accessory without permanently sticking a mount to the cabin trim.

No Dashboard Adhesive Required

The supplier specifies a mechanical clamping design that mounts to the display frame without glue or adhesive tape on the dashboard. This makes the holder removable without intentionally bonding it to interior trim.

No Adhesive Does Not Mean No Possible Contact Marks

Because the mount physically contacts the display frame, installation pressure, trapped dirt or long-term movement can still potentially leave temporary marks. Keep all contact surfaces clean and do not overtighten the mounting mechanism.

Telescopic Adjustment Range

Supports Different Display-Edge Profiles

The supplier states that the clamp is designed to work with display-edge thicknesses from approximately 5 to 18 mm and supports both rounded and square edge profiles.

Silicone-Cushioned Contact Points

The display-contact areas use thick silicone cushioning between the mount and the center-screen frame.

The soft contact layer helps reduce hard-surface rubbing, rattling and vibration transfer between the metal support arm and the screen frame during normal driving.

⚠️ Silicone Cushioning Helps Reduce Contact Marks — It Does Not Guarantee a Scratch-Free Screen

Keep the silicone pads and display frame free from sand, grit and other abrasive debris before installation. Do not slide or force the mount against the screen frame while dirt is trapped between the surfaces.

Thickened Alloy Support Arm

The supplier describes the telescopic support structure as a thickened heavy-duty alloy arm intended to provide a more stable mounting base over uneven roads and during normal cornering.

Vehicle Motion Can Still Cause Some Movement

No phone holder can guarantee completely vibration-free performance in every road condition. Mount stability depends on installation, arm extension, phone weight, road surface and the selected attachment. Recheck the clamp if excessive movement develops.

Two Phone-Mount Attachment Styles

⚠️ Magnetic Mount Compatibility Depends on the Phone / Case

The current page confirms a magnetic mounting pad but does not publish MagSafe certification, magnet strength, compatible phone models or case-thickness limits. Magnetic holding performance can vary depending on the phone and case being used.

No Wireless Charging Specification Is Published

The magnetic attachment should not be described as a wireless charger, MagSafe charger or Qi charger. The current product page does not publish any charging electronics, wattage or wireless-charging capability.

Standard 17 mm Ball Joint

The supplier specifies a standard 17 mm ball-joint connection between the support arm and phone-holder attachment. The included gravity cradle and magnetic pad can be swapped on this joint.

Vehicle Compatibility

Exact Model-Year Range Is Not Published

The current exact product page lists Tesla Model 3 and Model Y but does not publish a specific model-year breakdown. If your vehicle has a refreshed, modified or aftermarket center display, compare the screen-frame shape and available mounting clearance before ordering.

⚠️ Aftermarket Screen Accessories Can Affect Fitment

Thick screen protectors, decorative screen frames, swivel mounts or other aftermarket display accessories may change the available edge thickness or mounting clearance. Measure and compare before installation.

Installation Overview

1. Clean the Screen Frame
Remove dust, grit and oils from the rear and edge areas where the silicone contact pads will sit.

2. Adjust the Telescopic Arm
Set the arm length to suit the center display and your preferred phone position.

3. Position the Clamp
Place the mount carefully around the intended rear-screen frame area.

4. Secure the Mount
Tighten the mechanical mounting system only enough to keep the holder stable.

5. Install the Preferred Attachment
Fit either the gravity cradle or magnetic pad onto the 17 mm ball joint.

6. Adjust the Viewing Angle
Rotate the phone attachment to a comfortable position without blocking the vehicle display or driver's field of view.

7. Stability Check
Before driving, confirm that the arm, clamp, phone attachment and phone are secure.

⚠️ Do Not Overtighten Against the Touchscreen

Use only enough clamping force to keep the mount stable. Excessive tightening can place unnecessary pressure on the display housing or silicone pads. Stop installation if the screen frame flexes, creaks or shows unusual pressure.

⚠️ Keep the Touchscreen & Driving View Clear

Position the phone so it does not block important vehicle information, touchscreen controls, mirrors or the driver's forward field of view. Reposition the holder if it interferes with normal vehicle operation.

⚠️ Avoid Adjusting the Phone While Driving

Set the phone position before driving whenever possible. Follow local laws regarding phone use and mounted-device placement while operating the vehicle.

Routine Care

Clean the Silicone Pads
Periodically wipe the contact pads and screen frame to remove dust and grit.

Check the Clamp
Recheck mounting tension if the arm begins to move after repeated road vibration.

Inspect the Ball Joint
Make sure the 17 mm joint remains secure after changing between the gravity cradle and magnetic pad.

Remove Before Service if Necessary
If vehicle service requires access around the center display, remove the holder first to avoid accidental interference.

Specifications

⚠️ Unpublished Specifications

The current exact product page does not publish maximum phone weight, supported phone width, magnet strength, MagSafe certification, wireless-charging capability, alloy grade, product weight or a specific model-year fitment range. Do not add these specifications unless separately confirmed for this exact product.

Confirmed Included Components

1 × Telescopic Screen-Mount Support Assembly

1 × Gravity Phone Cradle

1 × Magnetic Phone-Mount Pad

Quick Answers